How to replace the stator of a single screw pump?

Jul 07, 2025

Leave a message

Hey there! As a supplier of single screw pumps, I often get asked about the ins and outs of pump maintenance. One of the more involved tasks is replacing the stator of a single screw pump. Today, I'm gonna walk you through the whole process step by step.

Why Replace the Stator?

First off, you might be wondering why you'd need to replace the stator in the first place. Well, the stator is a crucial part of the single screw pump. It's made of elastomer material, and over time, it can wear out due to continuous contact with the rotor and the pumped fluid. Signs that your stator might need replacing include reduced pump performance, leaks, or unusual noises during operation.

Tools You'll Need

Before you start the replacement process, make sure you've got all the necessary tools on hand. You'll need a set of wrenches, a puller (for removing the old stator), a torque wrench (to ensure proper tightening), a clean cloth for wiping down parts, and of course, the new stator that matches your pump model.

Step 1: Preparation

Safety first! Before you do anything, make sure the pump is completely shut off and disconnected from the power source. This will prevent any accidental starts while you're working on it. Next, relieve the pressure in the pump system. You can do this by opening the appropriate valves to let the fluid drain out. It's also a good idea to wear protective gear like gloves and safety glasses to avoid any injuries.

Step 2: Remove the Pump Head

The pump head is where the stator is located. Use your wrenches to loosen and remove the bolts that hold the pump head in place. Be careful not to drop or misplace any of the bolts. Once the bolts are removed, gently lift off the pump head and place it on a clean, flat surface.

Step 3: Take Out the Old Stator

Now it's time to remove the old stator. This can be a bit tricky, especially if it's been in there for a while. You can use a puller to carefully grip the stator and pull it out. If the stator is stuck, you might need to apply some lubricant to help loosen it up. Just be careful not to damage the pump housing while you're doing this.

Step 4: Inspect the Pump Housing

With the old stator out, take a good look at the pump housing. Check for any signs of damage, such as scratches, cracks, or corrosion. If you notice any issues, it's a good idea to address them before installing the new stator. You can clean the housing with a cloth to remove any debris or old lubricant.

Step 5: Install the New Stator

Before you install the new stator, make sure it's the correct size and model for your pump. Apply a thin layer of lubricant to the inside of the pump housing and the outside of the new stator. This will make it easier to insert the stator and ensure a proper fit. Carefully lower the new stator into the pump housing, making sure it's aligned correctly. Use your hands to gently press it into place.

Step 6: Reassemble the Pump Head

Once the new stator is installed, it's time to put the pump head back on. Line up the pump head with the housing and insert the bolts. Use your torque wrench to tighten the bolts to the manufacturer's recommended specifications. This is important to ensure a proper seal and prevent leaks.

Step 7: Reconnect the Pump

Now that the pump head is back on, it's time to reconnect the pump to the power source and the fluid system. Make sure all the connections are secure and that there are no leaks. Once everything is connected, you can turn on the pump and check for proper operation. Listen for any unusual noises and monitor the pump performance to make sure it's working as it should.

745A9450745A9562

Tips and Tricks

  • Lubrication is Key: Using the right lubricant can make the stator replacement process much easier. Make sure to choose a lubricant that's compatible with the elastomer material of the stator.
  • Follow the Manual: Every single screw pump is different, so it's important to follow the manufacturer's instructions when replacing the stator. This will ensure that you do it correctly and avoid any potential problems.
  • Keep Spares on Hand: It's a good idea to keep a spare stator in stock so that you can quickly replace it if needed. This will minimize downtime and keep your operations running smoothly.

Conclusion

Replacing the stator of a single screw pump might seem like a daunting task, but with the right tools and a little know-how, it's definitely doable. By following these steps and taking the necessary precautions, you can ensure that your pump continues to perform at its best.

If you're in the market for a new Mono Screw Pump or a Feeding Type Single Screw Pump, or if you have any questions about stator replacement or pump maintenance, don't hesitate to reach out. We're here to help you find the right solutions for your pumping needs.

References

  • Manufacturer's Manual for Single Screw Pumps
  • Industry Best Practices for Pump Maintenance